Universal dosing with the KOBOLD ADI-Z

November 16th, 2007

The new universal KOBOLD ADI-Z dosing device offers varied functions such as flow display, flow quantity counter, dosing functions and the display and monitoring of pressure and temperature threshold values in one device.

 

An added benefit of this device is the comfortable operation, and its clearly arranged and easily readable displays.

The 4 1/2-character digital display shows the momentary flow reading. The 2-line LCD displays both the current accumulated flow quantity as well as the pressure and temperature with the use of two additional sensor inputs. A comfortable batch function controls 2 switching outputs, either individually or in loop operation as desired. There are also 2 control inputs for remote start and stop. The incoming signals are digitized and processed in a µ-processor. The scaling of the display, the switch actuation point setting, save function and linearization are achieved using the three programming keys.

The device has the following flow controller functions as standard:

  • Free scaling using teach-In or by entering the impulse rate
  • MIN/MAX memory
  • 9-point sensor linearization (only frequency input)

In addition to the standard functions the device can also be fitted with an analogue output (0(4)-20 mA) and a sensor supply (5/12/24 VDC).

For pricing, please contact our sales team at +603-8024-4948 or e-mail saleservice@isicontrol.com

LPIV - LOW PROFILE INSERTION VORTEX METER

October 19th, 2007

The low profile insertion vortex flow meter is a cross pollination of an inline meter and an insertion meter. The purpose is to simplify the installation and eliminate human error when installing a flow meter. The insertion depth is always held to an exact position, and the meter will always point up stream, eliminating calibration variables. The meter has a low profile and can be installed in any orientation, vertically or horizontally around the pipe. Since most problems with the operation of an insertion meter is installation related the start up reliability of the meter reading is very high.

3sm1.jpg  1sm.jpg There are no other parts required, other than the meter during installation. The mounting assembly welds directly on the outside of the pipe. The radius of the mounting assembly is machined to fit the diameter of the pipe, from two inch to twenty four inches in diameter. There is an arrow machined into the mounting assembly showing the direction of flow. Once the mounting assembly is welded to the pipe, the insertion bar can then be inserted into the mounting assembly.

The insertion bar is designed to have no leak paths to the sensors or the electronics. All mechanical assemblies on the insertion bar are electron beam welded with no O rings or compression seals. If for any reason the insertion bar is damaged, it can be replaced without removing anything off the pipe. There are two sizes of insertion bars, one for two - four inches and one for six - twenty four inches; therefore one spare part can fit many lines sizes and could be interchangeable.

The meter has been designed for safety. There is a pin which is inserted into the mounting assembly once the insertion bar is inserted into the pipe. This pin serves two purposes. The first is to align the meter with the flow; the second is to prevent the meter from coming out under pressure. The pin can only be installed with zero line pressure. When pressure is applied, the pin is locked in place and cannot be removed. There is also a large nut which screws down over the insertion bar onto the mounting assembly. This nut also holds the insertion in place and keeps it from coming out of the line under pressure. When pressure is applied to the line, the insertion bar cannot be removed; even if someone removes the holding nut, the pin is still in place.These meters include our Smart Transmitter Electronics, “MicroTel”. There are six digits of rate and eight digits of totalization. All parameters can be modified via a keypad. The electronics is a two wire device, 4 to 20 mA and can be remote mounted over three hundred feet from the meter. There is also a serial port to read and down load data into memory.

For pricing, please contact our sales team at +603-8024-4948 or e-mail saleservice@isicontrol.com

WHERE FLOW MEASUREMENT MEETS INNOVATION

October 19th, 2007
  • Our Vortex designs are Universal Among all Fluid Types.
  • One Piece Construction for all Vortex Elements.
  • Unlimited Velocity Range
  • Our Dual Sensors NEVER come into contact with the process fluid, giving them an almost unlimited life span.
  • Can handle process pressures over 1000 psig.
  • No holes to clog
  • No moving parts
  • No internal leak paths.
  • All welded construction.
  • Two Wire, Low Power MASS flow capabilities.
  • Completely Maintenance Free
  •  For further question, please contact us at saleservice@isicontrol.com

    FAQ - Nice Instrumentation

    October 19th, 2007

    3zoom.jpg3sm.jpg 

    - Why use a Vortex Meter over any other meter? 

    1. There is a wide measurement range.
    2. There are no moving parts to wear out or fail.
    3. The same meter measures steam, gas, and liquids.

    - How does the meter need to be installed?

    1. The meter can be installed vertically, horizontally or upside down.
    2. The meter can be used in virtually any line size. (ex. 3/4″ - 48″)
    3. The insertion meter only needs a 1 1/2″ hole in the pipe, no need to cut the pipe.

    - How do you interface with the vortex meter?

    1. Our smart-transmitter is a two wire device, with serial communications.
    2. The meter comes with a standard multi pin connector, no wiring internally is required
    3. The MicroTel can be remotely mounted up to 300 feet from the meter for easy visibility.

    - Please ask us any questions or comments by sending us an email saleservice@isicontrol.com . The engineers at Nice Instrumentation are dedicated to help you with your application needs.

    OUR PRODUCT

    October 4th, 2007

    det_buoyancy.jpg

    COMPANY INTRODUCTION

    October 4th, 2007

    ISI Control Sdn Bhd is a Malaysia Process Control Equipments Supplier. We are dealing with process control systems and process control equipments for level, flow, pressure, temperature and analytical measurement.

    As Malaysia Process Control Equipments Supplier we also design, fabricate, install and comission complete control loop by packaging or integrate other process control systems with our product range to suit the various process control requirement.

    At the same time we also providing engineering services such as maintaining and repairing of process control systems and process control equipments ; pre-commissioning or set-up services and man-power supply.